This tank has a 2.00 " diameter hose connection A 1/8 " NPT fitting for a drain cock Holes @ 18.00 " centers for and oil cooler Two pin mounts for attaching side frames Four mounting nuts on the grill side of the tank Comes with four 5/16 " NPT x 4 " bolts with nuts, and a 1/8 " NPT plug Note: this tank set fits with Mercedes engine.

This tank has a 2.00 " diameter hose connection, six 1/4 " NC threaded nuts (two on the fan side four on the grill side) Two mounting bracket on each end to attach side frames and an expansion fitting

This tank has a 3.00 " diameter hose connection facing the ground 1.75 " diameter hose connection facing the engine Two 3/8 " NPT flanges

Inlet Tank : This tank has a 2.00 " diameter hose connection 6.25 " from the edge of the tank to the center of the hose connection A 1/4 " NPT flange at each end of the tank for drainage Outlet Tank : This tank has a 2.00 " hose connection 7.75 " from the edge of the tank to the center of the hose connection A hole on one end for the fill neck Holes @ 18.00 " centers to accommodate an oil cooler

Top bottom hose connections 2.50 " 6.00 " from end of tank to center of connection Bottom tank has double pins and holes for oil cooler

Both of these tanks are identical Each has a 2.00 " diameter hose connection 6.25 " from the edge of the tank to the center of the hose connection A 1/4 " NPT flange on either end of the tank for a drain cock or an expansion fitting.

This tank has a 2.00 " diameter hose connection A 3/8 " diameter expansion tube coming out of the top of the hose connection Two pin mounts for attaching side frames Four mounting nuts on the grill side of the tank

Two openin gs of 2.25 " O.D. pipe straight out One 1.00 " O.D. hose connection One 1/8 " N.P.T. fitting on side One bolt-on type filler at the center on the top front corner Built-in baffle

Inlet Tank : This tank has a 2.50 " diameter hose connection 1/4 " NPT flange on each end of the tank Outlet Tank : This tank has a 3.00 " diameter hose connection 1/4 " NPT flange on each end of the tank 1/4 " NPT x 3/8 " diameter 90o hose barb is provided.

This tank has a 3.00 " diameter hose connection pointing towards the ground 1.75 " diameter hose connection pointing towards the engine Two 3/8 " NPT flanges for drainage

This tank has a 3 bolt hole triangular flange

Two openings of 2.25 " O.D. 90 degree elbows facing down and out slightly to each end of tank One 1.00 " O.D. hose connection Two 1/8 " N.P.T. fittings, one on side and one in top corner (driver 's side) One bolt on type filler at the center of the slanted top Built-in baffle

One opening for 2.00 " O.D. pipe on a 45 degree bend facing down One 1.0 " O.D. hose connection One 1/8 " N.P.T. fitting on side One bolt-on type filler at the center on the top Built-in baffle

Two openings of 2.50 " O.D. pipe straight out One 1.00 " O.D. hose connection One 1/8 " N.P.T. fitting on side One bolt-on type filler at the center on the top front corner Built-in baffle

Two openings, one is a 2.25 " O.D. 90 degree elbow facing down (passenger side), one is a 2.25 " O.D. pipe straight out (driver 's side) One 1.00 " O.D. hose connection One 1/8 " N.P.T. fitting on side One 1/4 " fitting on lower corner passenger side One bolt-on type filler at the center on the top front corner Built in baffle

One opening of 2.50 " O.D. pipe coming out on approximately a 30 degree angle towards centre of tank. One 1.00 " O.D. hose connection. One 1/8 " N.P.T. fitting on side One bolt-on type filler at the center on the top front corner Built-in baffle

One opening of 2.50 " O.D. pipe coming out on approximately 30 degree angle towards the center of the tank One 1.00 " O.D. hose connection One 1/8 " N.P.T. fitting on side One bolt-on type filler at the center of the slanted top Built-in baffle

Low flow tank with "rounded " header has one 1.00 " O.D. hose connection on driver 's side lower section facing passenger side (on 75 degree angle) One 1.00 " O.D. hose connection on passenger 's side of center facing passenger side and slightly down. One 3/8 " O.D. hose connection on passenger side facing engine Two bolt-on type flanges on top of tank One 1/4 " N.P.T. fitting in built-in baffle for check valve Top driver 's side of tank is cut lower to accommodate air to air cooler NOTE: Check valve installed

This tank has a 3 bolt hole triangular flange

This tank has triangular flange with 3 bolt holes, and a channel shaped bracket with a 9/16 " hole welded in center of the tank

This blank tank has rounded corners. There is a 1/4 " NPT flange on each end. Note: matches with tank #FR 459LF

This tank is the same as tank #FR 453LF, except both hose connections are on the driver side of center, and the baffle splits the tank front to back instead of left to right

This tank has a "rounded " header, and a bolt-on type flange in the center of the tank with four 3/8 " NC threaded holes

This low flow tank has a "rounded " header There is a 1.25 " diameter hose connection facing straight out 1/4 " NPT flange on the end

This tank has a "rounded " header 3.00 " diameter hose connection 1/4 " NPT flange on the end Note: matches tank #FR 458

This tank has a 3.00 " diameter hose connection 1/4 " NPT flange for a drain 14 plate oil cooler with 18.00 " centers

This frame has eleven 3/8 " NC theaded hole along the back Six 1/4 " threaded holes along the edges The end flanges have fourteen bolt holes (three of them threaded).

This tank has a 2.75 " diameter hose connection 3.00 " long 1/4 " NPT flange on the grill side for a drain Two 5/8 " NC studs 3.00 " long @ 18.00 " centers A 14 plate oil cooler @ 18.00 " centers (1418PC) (replaces bundle oil cooler).

This tank has a 2.75 " diameter hose connection (comes out of the tank at 90 degree then angles up towards the engine) A 10 plate 18.00 " center oil cooler(1018PC) A 1/4 " NPT flange A 1/2 " NPT flange

This tank has a 2.75 " diameter hose connection on the passenger side that bends upwards 1/4 " NPT flange for a drain cock 3/4 " NPT flange 10 plate oil cooler with 18.00 " centers and 1.00 " NPT fittings

This tank has a 3.00 " diameter hose connection Two 5/8 " threaded studs @ 8.00 " centers 1/4 " NPT flange on the grill side for a drain cock.

This tank has a 3.00 " diameter hose connection 14 plate oil cooler with 18.00 " centers Two 5/8 " NC threaded studs @ 22.00 " centers for mounting purposes.

2.00 " top btm hose connection top connection 6.00 " from end of tank to center of connection bottom connection 7.50 " from end of tank to center of connection, 18.00 " between oil cooler holes

2.50 " hose conn., 5.75 from end of tank to center of conn., available in brass and steel (solder dipped)

2.00 " hose connection, 2.00 " from end of tank to center of connection

hose connection 2.50 "; 5.75 " from end of tank to center of connection

both hose conn. 2.50 " available in brass or steel(solder dipped)

2.00 " hose connection, 6.00 " from end of tank to center of connection

hose conn. 5.75 " from end of tank to center of connection. Conn. 2.50 " diameter, 1 - 1/4 " NPT fitting on end of tank for drain valve or barb fitting