2.50 " hose connection with 18.00 " centers oil cooler holes; Hose Connection extends out 4.25 " from Tank

Two bolt on type flanges with two 3/8 " N.C. threaded holes in each One 3/8 " N.P.T. One 1/4 " N.P.T. facing engine One 1/2 " N.P.T. fitting on grille side One flange connection on baffle with two 5/16 " N.C. threaded holes One hole for filler neck on top front edge

One 2.25 " O.D. hose connection in center facing engine Two 1/8 " N.P.T. fittings on top One hole for filler neck on top One 3/8 " N.P.T. fitting on passenger end of tank One 1.00 " O.D. hose connection out baffle on passenger side - angled to passengers end of tank Fifteen 5/16 " N.C. threaded holes in baffle.

Two bolt on type flanges with two 3/8 " N.C. threaded holes in each One 1/4 " and one 1/2 " N.P.T. fitting facing engine One 5/8 " O.D. hose connection on lower passenger side facing engine One hole on top slope for filler neck One bolt on type flange on front driver side One 1/2 " N.P.T. fitting on front driver side One bolt on type flange in baffle

Two bolt-on type connections with two 3/8 " N.C. threads One bolt-on type filler with four 5/16 " N.C. threads One 3/4 " N.P.T. fitting One 1/2 " N.P.T. fitting Two 3/8 " N.P.T. fittings One 1/4 " N.P.T. fitting Built-in baffle

Two flanges with two 3/8 " N.C. threaded holes in each Two 3/8 " N.P.T. fittings Two round brackets One bracket on top One 1.75 " hole on top for filler neck One flange in built-in baffle with two 5/16 " N.C. threads One bar on built-in baffle with five 5/16 " N.C. threaded holes.

Twenty 5/16 " N.C. threads in built-in baffle One 2.25 " O.D. hose connection on driver side One 1.00 " O.D. hose connection on passenger side in built-in baffle One 1.75 " pipe on front for filler neck Three 1/4 " N.P.T. fittings Two brackets fitted on top of tank

Sixteen 5/16 " N.C. threaded holes in built-in baffle One 2.25 " hose connection on driver side One 1.00 " O.D. hose connection on passenger side One 1.75 " pipe on front for filler neck Three 1/4 " N.P.T. fittings

Two 1.50 " O.D. 90 degree elbows facing down and slightly out on each end One 1.00 " O.D. hose connection One 1/2 " N.P.T fitting One 3/8 " N.P.T. fitting Fifteen 5/16 " N.C. threaded holes in built-in baffle One 1.25 " hole for filler neck on top passenger side

One 2.50 " O.D. hose connection at center One 3/4 " N.P.T. fitting One 1/2 " N.P.T. fitting One 1/8 " N.P.T. fitting Fifteen 5/16 " N.C. threaded holes in built-in baffle One 1.25 " hole for filler neck on top driver side

One 2.50 " O.D. hose connection in center One 1.00 " O.D. 90 degree hose connection on passenger side One 1/8 " N.P.T. fitting One 1.25 " hole on top passenger side for filler neck Built-in baffle

This tank has a 2.75 " diameter hose connection that bends 90 degree on approximately a 45 degree angle One 3/8 " NPT flange on each end of the tank

This tank has a 2.50 " diameter hose connection with a 45 degree elbow that points upwards Note: if you need this tank with an oil cooler, order tank #IN6381

Two flange connections with two 3/8 " N.C. threaded holes in each Two 1/4 " N.P.T fittings One 3/8 " N.P.T. fittings One 1/2 " N.P.T. fitting on front facing engine One 1.75 " filler hole on top driver side One 1/2 " N.P.T. fitting on driver side One flange on bottom with two 5/16 " N.C. threaded holes NOTE: Matches tank #IN642

This tank has a rectangular flange with four 3/8 " NC holes Two bottom mounting holes @ 26.62 " centers

This tank has two rectangular flanges with four 3/8 " NC threaded holes in each Two mounting brackets with a 1/2 " NC threaded hole in each One 1/4 " NPT flange The tank dips in the middle between the brackets to allow for a PTO

This tank has a rectangular flange with four 3/8 " NC holes Two bottom mounting holes @ 25.25 " centers Two corners on the header are rounded off

This tank has a 2.50 " diameter hose connection facing the engine 1/4 " NPT flange on the rise of the tank

This tank has a 2.50 " diameter hose connection on the passenger side of center One 1/4 " NPT flange The tank is shallow except where the hose connection and flange are located

This tank has one rectangular flange with four 3/8 " NC holes Two bottom mounting holes at 25.25 " centers Two corners on the header are rounded off

This tank has a 2.50 " diameter hose connection on the passenger side One 1/4 " NPT flange in the center of the tank

This driver side blank tank has a 1/4 " NPT flange on each end The tank is 1.50 " deep and the header corners on grille side are cut on a 45 degree angle

This passenger side tank has a 1.00 " diameter hose connection near the top A 1.25 " diameter hose connection near the bottom A baffle divides the tank width-wise at the center One 1/4 " NPT flange in each end Two corners of the header are cut on 45 degree angle.

This tank has a 2.50 " diameter hose connection on on the passenger side of the tank facing up and out at approximately 45 degrees One 1/4 " NPT flange on driver side One 1/8 " NPT flange on the bottom

Top and bottom flanges have 11 holes each, all drilled to clear 5/16 " bolts. One bracket on back of side frame channel. Various other holes for brackets, shrouds, etc. Note: frames are interchangeable.

Small end has 8 holes, 4 tapped 5/16 " and 4 drilled clearance 5/16 " bolts. Large end has 9 holes, 6 taped 5/16 " and 3 drilled clearance for 5/16 " bolts. Two mounting angles on back of frame, one has 5 holes with 5/16 " N.C. threads, the other has 4 holes drilled clearance for 3/8 " bolts. Various other holes for brackets, etc. NOTE: Frames are not interchangeable. Order left for driver side or right for passenger side or pairs.

Top and bottom flanges have 6 holes each, all drilled clearance for 5/16 " bolts. Top of frame has offset bracket with 5 header holes drilled clearance for 5/16 " bolts. Sides of frame have five 5/16 " N.C. threaded studs, three facing engine and two facing grille. One angle bracket on back with 1.06 " diameter hole. Two sleeves welded on gussets to accommodate cross bars. Various other holes for brackets, mounting, etc. Note: frames are not interchangeable. Order left for driver

Cross flow bottom frame. Both flanges step down 1/4 " at gussets. Both flanges have 10 holes, 4 tapped 5/16 " N.C. and 6 drilled clearance for 5/16 " bolts. Channel is cut-out in center to accommodate bolts on mounting bracket. Frame has a total of 31 holes all tapped 5/16 " N.C. for brackets and shroud, etc. for mounting bracket.

This tank has a 2.50 " diameter hose connection 5.50 " from the edge of the tank to the center of the hose connection 1/4 " NPT fitting on end for an expansion tube

2.50 " hose connection, extends 4.25 " out from tank, 6.50 " from end of tank to center of connection

Top Tank : This tank has a 2.50 " diameter hose connection facing towards the engine 1/4 " NPT flange for an expansion barb Bottom Tank : This tank has a 2.50 " diameter hose connection facing downward from the radiator 1/4 " NPT fitting for a drain cock Note: This tank kit can be ordered in brass - #IN9214

Top Tank : This tank has a 2.50 " diameter hose connection 4.00 " from the edge of the tank to the center of the hose connection 1/4 " NPT flange Bottom Tank : This tank has a 2.50 " diameter hose connection 5.50 " from the edge of the tank to the center of the hose connection 1/4 " NPT flange for a drain cock Holes @ 18.00 " centers to accommodate on oil cooler

Inlet Tank : This tank has a 2.50 " diameter hose connection 5.75 " from the edge of the tank to the center of the hose connection 1/4 " NPT flange Outlet Tank : This tank has a 2.50 " diameter hose connection on the end of the tank facing downward towards the ground 1/4 " NPT flange on the opposite end of the tank Note: this tank set matches brass kit #IN9215.

Inlet Tank : This tank has a 2.50 " diameter hose connection 5.75 " from the edge of the tank to the center of the hose connection 1/4 " NPT flange to accommodate a drain cock Outlet Tank : This tank has a 2.50 " diameter hose connection that points towards the ground 1/4 " NPT flange to accommodate an expansion tube This set comes wit a 1/4 " NPT drain cock, and a 1/4 " NPT x 3/8 " hose barb.

This tank has a 2 1/2 " diameter hose connection, and a 1/4 " NPT flange.

2.50 " hose connection

2.25 " hose connection, 4.00 " from end of tank to center of connection; 18.00 " centers oil cooler holes